On older colonials and ranches around Newtown Square, Edgemont, and Gradyville, fascia is the thin board that takes the beating: gutter hangers, ice, and splash from humid summers. Once winter temperatures drop, freeze-thaw pries open paint and joints; then spring humidity feeds rot in the end grain at rakes and corners. We see the same pattern near tree-lined streets toward Tyler Arboretum and along West Chester Pike toward the Corporate Campus—leaf-packed gutters hold water against the board until the face cups or the drip edge lifts. Repair is not a paint-over. We pull gutters only as far as needed, probe for soft spots behind aluminum wrap, and replace full lengths so splices do not sit over a hanger.
Delaware County code and common-sense flashing matter more than homeowners expect. Fascia must back up the drip edge and give gutters a solid nailing plane; if we sister a rotten section and leave the old drip edge short, water still runs behind the new board. On two-story eaves in Media, Broomall, and Wayne, we stage from the ground or a modest lift rather than walking steep slate or cedar that many 1950s roofs still carry. Aluminum wrap can hide a hollow board; we cut a test window or pull a few nails before quoting a ‘cap only’ job. If the soffit vents are clogged with nest material, we clear them so the new fascia does not trap moisture in the rafter tails.
Materials are chosen for this climate, not a catalog photo. Primed pine or PVC for full replacements where rot has reached the rafter ends; pre-finished aluminum coil stock when the wood is still sound and the homeowner wants a low-maintenance face. We match existing gutter profiles so the new fascia does not leave a gap at the hanger. Hidden fasteners and sealed butt joints keep driving rain from Newtown Square storms out of the end grain. We do not wrap over active leaks or leave old rusty spikes in place—those pull out of wet wood the first time ice loads the gutter. Work is scheduled Mon–Fri 8am–6pm and Saturday mornings so occupied homes stay livable.
A fascia job that ignores the drip edge, kick-out flashing at chimneys, or the first course of shingles is a callback waiting to happen. We photograph the eave before and after, show you the cut-out rot, and leave the site broom-clean. If the board is only stained, we can sand, prime, and recaulk; if it is spongy, replacement is the honest path. Owner-operated from 3475 West Chester Pike, we give an on-site look rather than a phone guess, because every Newtown Square eave has a different mix of wrap, paint, and hidden rot.
Technician insight
In Newtown Square the thing that catches people out is aluminum wrap over a hollow board—especially on 1950s ranches toward Gradyville and Edgemont. Humid summers and leaf-packed gutters near the arboretum keep the back of the board wet while the face still looks fine. Homeowners paint the wrap and think they are done; the first ice load pulls the hangers out of mush. We always cut a small window or pull hangers before we call it a wrap-only job.
Wrapped eave on a two-story colonial near West Chester Pike
Gutters were pulling away after a cold snap. We found the aluminum cap hiding soft pine at every hanger, with rafter tails still mostly sound. We replaced the fascia in full lengths, reset the drip edge, and rehung the gutters into new wood. The eave stayed tight through the next freeze without another pull-away.
Roof Fascia Repair Services We Offer
✓Wood Fascia Board Replacement
Full-length primed pine or PVC boards where rot has reached rafter tails, common on older Newtown Square and Edgemont colonials.
✓Aluminum Fascia Cap Installation
Pre-finished coil wrap over sound wood to shed humid-summer splash and hide weathered paint without trapping moisture.
✓Rake and Eave Rot Repair
Targeted replacement at gable rakes and outside corners where end grain soaks up freeze-thaw water.
✓Gutter and Fascia Reattachment
Reset hangers into solid new board so ice and leaf loads from tree-lined streets do not pull the system off the eave.
✓Painted Fascia Restoration
Sand, prime, and recaulk when the board is still hard—honest alternative to full replacement on well-kept Wayne and Broomall homes.
✓Ice Dam Fascia Repair
Replace boards crushed or stained by winter ice along Delaware County eaves, then correct the drip edge so it does not repeat.
✓Soffit and Fascia Combination Repair
Open clogged soffit vents and replace both faces so new fascia does not seal moisture into the rafter bay.
Roof Fascia Repair Cost in Newtown Square, PA
| Service | Typical Range | What Affects It |
|---|---|---|
| Spot rot repair (short run) | $250–$600 | Access, wrap vs. wood, and whether gutters must come down |
| Single-elevation fascia replacement | $800–$2,200 | Length, two-story staging, material (pine, PVC, or aluminum) |
| Aluminum fascia wrap (sound wood) | $12–$22 per linear foot | Color match, rake returns, and existing gutter profile |
| Gutter reset with fascia work | $150–$450 added | Hanger type and whether hidden hangers need new board |
| Soffit vent clearing with fascia | $100–$350 | Nest material, perforated vs. continuous vent |
Ranges are typical for Newtown Square, PA and confirmed with an exact written quote before any work starts.
How it works
- 1
On-Site Probe And Photo
We meet at the house, pull a short gutter section if needed, and probe for soft wood behind wrap so the quote matches what is actually there.
- 2
Protect And Stage
Ladders or a small lift on two-story eaves; tarps over plantings and walkways typical of Newtown Square lots.
- 3
Remove And Replace
Cut out rotten lengths, set new board or wrap, reset drip edge and hangers, seal joints against driving rain.
- 4
Gutter Reset And Cleanup
Rehang gutters true, test a hose run, haul debris, and walk the eave with you before we leave.
Pricing
Most Newtown Square fascia repairs are quoted after we see the eave—not from photos—because wrap can hide rot. Typical work falls in modest ranges; long two-story runs, PVC, or full gutter reset move the number.